Slovakia: Compression Type Mould Market 2024

Compression Type Mould Market Size in Slovakia

In 2022, the Slovak compression type mould market increased by X% to $X, rising for the second year in a row after two years of decline. Over the period under review, consumption recorded a perceptible downturn. Compression type mould consumption peaked at $X in 2018; however, from 2019 to 2022, consumption remained at a lower figure.

Compression Type Mould Production in Slovakia

In value terms, compression type mould production amounted to $X in 2022 estimated in export price. In general, the total production indicated a resilient increase from 2012 to 2022: its value increased at an average annual rate of X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations being recorded throughout the analyzed period. Based on 2022 figures, production decreased by X% against 2020 indices. The most prominent rate of growth was recorded in 2014 when the production volume increased by X%. Over the period under review, production hit record highs at $X in 2016; however, from 2017 to 2022, production stood at a somewhat lower figure.

Compression Type Mould Exports

Exports from Slovakia

In 2022, exports of injection or compression type moulds for rubber or plastics from Slovakia shrank notably to X units, declining by X% against the previous year's figure. In general, exports, however, recorded a prominent increase. The growth pace was the most rapid in 2013 with an increase of X%. Over the period under review, the exports reached the peak figure at X units in 2018; however, from 2019 to 2022, the exports remained at a lower figure.

In value terms, compression type mould exports reduced dramatically to $X in 2022. Over the period under review, exports, however, saw a prominent expansion. The growth pace was the most rapid in 2021 when exports increased by X% against the previous year. As a result, the exports attained the peak of $X, and then fell dramatically in the following year.

Exports by Country

Germany (X units) was the main destination for compression type mould exports from Slovakia, with a X% share of total exports. Moreover, compression type mould exports to Germany exceeded the volume sent to the second major destination, the Czech Republic (X units), fivefold. Poland (X units) ranked third in terms of total exports with a X% share.

From 2012 to 2022, the average annual rate of growth in terms of volume to Germany totaled X%. Exports to the other major destinations recorded the following average annual rates of exports growth: the Czech Republic (X% per year) and Poland (X% per year).

In value terms, the largest markets for compression type mould exported from Slovakia were the Czech Republic ($X), Germany ($X) and Austria ($X), together accounting for X% of total exports. Poland, Serbia, France, the Netherlands, India, Portugal, the United States, Hungary and Russia lagged somewhat behind, together comprising a further X%.

Among the main countries of destination, Serbia, with a CAGR of X%, recorded the highest rates of growth with regard to the value of exports, over the period under review, while shipments for the other leaders experienced more modest paces of growth.

Export Prices by Country

The average compression type mould export price stood at $X per unit in 2022, surging by X% against the previous year. In general, the export price, however, saw a relatively flat trend pattern. The most prominent rate of growth was recorded in 2020 an increase of X% against the previous year. Over the period under review, the average export prices reached the peak figure at $X per unit in 2012; however, from 2013 to 2022, the export prices remained at a lower figure.

Prices varied noticeably by country of destination: amid the top suppliers, the country with the highest price was Austria ($X per unit), while the average price for exports to Germany ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was recorded for supplies to Serbia (X%), while the prices for the other major destinations experienced more modest paces of growth.

Compression Type Mould Imports

Imports into Slovakia

In 2022, overseas purchases of injection or compression type moulds for rubber or plastics decreased by X% to X units, falling for the fourth consecutive year after two years of growth. In general, imports recorded a abrupt decrease. The pace of growth appeared the most rapid in 2017 when imports increased by X%. Imports peaked at X units in 2018; however, from 2019 to 2022, imports remained at a lower figure.

In value terms, compression type mould imports declined notably to $X in 2022. Over the period under review, imports, however, continue to indicate tangible growth. The pace of growth appeared the most rapid in 2017 with an increase of X%. Over the period under review, imports attained the maximum at $X in 2018; however, from 2019 to 2022, imports stood at a somewhat lower figure.

Imports by Country

In 2022, China (X units) constituted the largest supplier of compression type mould to Slovakia, accounting for a X% share of total imports. Moreover, compression type mould imports from China exceeded the figures recorded by the second-largest supplier, Austria (X units), threefold. South Korea (X units) ranked third in terms of total imports with a X% share.

From 2012 to 2022, the average annual growth rate of volume from China was relatively modest. The remaining supplying countries recorded the following average annual rates of imports growth: Austria (X% per year) and South Korea (X% per year).

In value terms, China ($X), Germany ($X) and Austria ($X) constituted the largest compression type mould suppliers to Slovakia, with a combined X% share of total imports. The Czech Republic, Italy, South Korea, Portugal, Serbia, France and Poland lagged somewhat behind, together comprising a further X%.

Serbia, with a CAGR of X%, recorded the highest growth rate of the value of imports, among the main suppliers over the period under review, while purchases for the other leaders experienced more modest paces of growth.

Import Prices by Country

The average compression type mould import price stood at $X per unit in 2022, jumping by X% against the previous year. Overall, the import price posted significant growth. The growth pace was the most rapid in 2020 an increase of X% against the previous year. Over the period under review, average import prices hit record highs in 2022 and is likely to continue growth in the near future.

Prices varied noticeably by country of origin: amid the top importers, the country with the highest price was the Czech Republic ($X per unit), while the price for Poland ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was attained by Italy (X%), while the prices for the other major suppliers experienced more modest paces of growth.

Source: IndexBox Platform

Frequently Asked Questions (FAQ) :