Asia: Numerically Controlled Lathe Market 2020

Numerically Controlled Lathe Market Size in Asia

The revenue of the numerically controlled lathe market in Asia amounted to $X in 2017, jumping by X% against the previous year. The numerically controlled lathe consumption continues to indicate a relatively flat trend pattern. The growth pace was the most rapid in 2009, when market value increased by X% against the previous year. Over the period under review, the numerically controlled lathe market reached its peak figure level of $X in 2014; however, from 2015 to 2017, it failed to regain its momentum.

Numerically Controlled Lathe Production in Asia

The numerically controlled lathe production amounted to X units in 2017, surging by X% against the previous year. The total output volume increased an average annual rate of +X% from 2007 to 2017; the trend pattern remained consistent, with only minor fluctuations throughout the analyzed period. The most prominent rate of growth was recorded in 2008, when the output figure increased by X% y-o-y. Over the period under review, the numerically controlled lathe production reached its peak figure volume in 2017, and is likely to continue its growth in the immediate term.

Numerically Controlled Lathe Exports in Asia

In 2017, the amount of numerically controlled horizontal lathes, turning centres, for removing metal exported in Asia stood at X units, increasing by X% against the previous year. The total exports indicated a moderate expansion from 2007 to 2017: its volume increased at an average annual rate of +X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations throughout the analyzed period. Based on 2017 figures, the numerically controlled lathe exports increased by +X% against 2013 indices. The pace of growth appeared the most rapid in 2011, when exports increased by X% against the previous year. Over the period under review, the numerically controlled lathe exports reached its maximum volume in 2017, and are likely to continue its growth in the near future.

In value terms, numerically controlled lathe exports totaled $X in 2017. The numerically controlled lathe exports continue to indicate a relatively flat trend pattern. The level of exports peaked of $X in 2012; however, from 2013 to 2017, it stood at a somewhat lower level.

Numerically Controlled Lathe Exports by Country in Asia

In 2017, Japan (X units) was the key exporter for numerically controlled horizontal lathes, turning centres, for removing metal, generating X% of total exports. China (X units) occupied the second position in the ranking, followed by South Korea (X units) and Taiwan, Chinese (X units). All these countries together occupied near X% share of total exports. Thailand (X units) followed a long way behind the leaders.

Japan experienced a relatively flat trend pattern of numerically controlled horizontal lathes, turning centres, for removing metal exports. At the same time, Taiwan, Chinese (+X%), Thailand (+X%), China (+X%) and South Korea (+X%) displayed positive paces of growth. Moreover, Taiwan, Chinese emerged as the fastest growing exporter in Asia, with a CAGR of +X% from 2007-2017. Thailand (-X%), South Korea (-X%), China (-X%) and Taiwan, Chinese (-X%) significantly weakened its position in terms of the global exports, while the shares of the other countries remained relatively stable throughout the analyzed period.

In value terms, Japan ($X) remains the largest numerically controlled lathe supplier in Asia, making up X% of global exports. The second position in the ranking was occupied by South Korea ($X), with a X% share of global exports. It was followed by Taiwan, Chinese, with a X% share.

In Japan, numerically controlled lathe exports contracted by an average annual rate of -X% over the period from 2007-2017. The remaining exporting countries recorded the following average annual rates of exports growth: South Korea (-X% per year) and Taiwan, Chinese (+X% per year).

Numerically Controlled Lathe Export Prices by Country in Asia

In 2017, the numerically controlled lathe export price in Asia amounted to $X thousand per unit, therefore, remained relatively stable against the previous year. The numerically controlled lathe export price continues to indicate a significant deduction. The most prominent rate of growth was recorded in 2011, when the export prices increased by X% y-o-y. Over the period under review, the export prices for numerically controlled horizontal lathes, turning centres, for removing metal attained its peak figure level of $X thousand per unit in 2013; however, from 2014 to 2017, it stood at a somewhat lower level.

Export prices varied noticeably by the country of destination; the country with the highest export price was Thailand ($X thousand per unit), while China ($X thousand per unit) was amongst the lowest.

From 2007 to 2017, the most notable rate of growth in terms of export prices was attained by China (+X% per year), while the other leaders experienced a decline in the export price figures.

Numerically Controlled Lathe Imports in Asia

In 2017, approx. X units of numerically controlled horizontal lathes, turning centres, for removing metal were imported in Asia; going up by X% against the previous year. The total imports indicated a moderate increase from 2007 to 2017: its volume increased at an average annual rate of +X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations throughout the analyzed period. Based on 2017 figures, the numerically controlled lathe imports increased by +X% against 2015 indices. The pace of growth was the most pronounced in 2010, when it surged by X% y-o-y. Over the period under review, the numerically controlled lathe imports reached its maximum volume of X units in 2011; however, from 2012 to 2017, it failed to regain its momentum.

In value terms, numerically controlled lathe imports amounted to $X in 2017. The total imports indicated a moderate increase from 2007 to 2017: its value increased at an average annual rate of +X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations throughout the analyzed period. The level of imports peaked of $X in 2014; however, from 2015 to 2017, it stood at a somewhat lower level.

Numerically Controlled Lathe Imports by Country in Asia

In 2017, China (X units), distantly followed by Turkey (X units), Japan (X units), Taiwan, Chinese (X units), Thailand (X units), South Korea (X units) and India (X units) were the key importers of numerically controlled horizontal lathes, turning centres, for removing metal, together constituting X% of total imports.

From 2007 to 2017, the most notable rate of growth in terms of imports, amongst the main importing countries, was attained by Taiwan, Chinese (+X% per year), while the other leaders experienced more modest paces of growth.

In value terms, China ($X) constitutes the largest market for imported numerically controlled horizontal lathes, turning centres, for removing metal in Asia, making up X% of global imports. The second position in the ranking was occupied by Japan ($X), with a X% share of global imports. It was followed by Turkey, with a X% share.

In China, numerically controlled lathe imports remained relatively stable over the period from 2007-2017. In the other countries, the average annual rates were as follows: Japan (+X% per year) and Turkey (+X% per year).

Numerically Controlled Lathe Import Prices by Country in Asia

The numerically controlled lathe import price in Asia stood at $X thousand per unit in 2017, going up by X% against the previous year. The numerically controlled lathe import price continues to indicate a relatively flat trend pattern. The pace of growth was the most pronounced in 2012, an increase of X% y-o-y. The level of import price peaked of $X thousand per unit in 2014; however, from 2015 to 2017, it stood at a somewhat lower level.

There were significant differences in the average import prices amongst the major importing countries. In 2017, the country with the highest import price was South Korea ($X thousand per unit), while Turkey ($X thousand per unit) was amongst the lowest.

From 2007 to 2017, the most notable rate of growth in terms of import prices was attained by Thailand (+X% per year), while the other leaders experienced more modest paces of growth.

Source: IndexBox Platform