Italy: Compression Type Mould Market 2024

Compression Type Mould Market Size in Italy

The Italian compression type mould market shrank to $X in 2022, remaining relatively unchanged against the previous year. The market value increased at an average annual rate of X% over the period from 2012 to 2022; however, the trend pattern indicated some noticeable fluctuations being recorded throughout the analyzed period. Over the period under review, the market hit record highs at $X in 2019; however, from 2020 to 2022, consumption remained at a lower figure.

Compression Type Mould Production in Italy

In value terms, compression type mould production expanded remarkably to $X in 2022 estimated in export price. In general, production, however, recorded a pronounced decrease. The most prominent rate of growth was recorded in 2020 with an increase of X%. Compression type mould production peaked at $X in 2014; however, from 2015 to 2022, production remained at a lower figure.

Join Us at HANNOVER MESSE 2024

Don’t miss your chance to connect with us directly. Schedule a personal meeting to dive deeper into how solutions.
Hall 002, Stand C10. 22 - 26 April 2024 | Hannover, Germany

Book Your Meeting

Compression Type Mould Exports

Exports from Italy

In 2022, overseas shipments of injection or compression type moulds for rubber or plastics decreased by X% to X units, falling for the fifth consecutive year after four years of growth. In general, exports recorded a abrupt decrease. The pace of growth appeared the most rapid in 2017 with an increase of X% against the previous year. As a result, the exports reached the peak of X units. From 2018 to 2022, the growth of the exports failed to regain momentum.

In value terms, compression type mould exports fell to $X in 2022. Over the period under review, exports showed a mild slump. The pace of growth appeared the most rapid in 2017 when exports increased by X%. As a result, the exports attained the peak of $X. From 2018 to 2022, the growth of the exports failed to regain momentum.

Exports by Country

Germany (X units) was the main destination for compression type mould exports from Italy, accounting for a X% share of total exports. Moreover, compression type mould exports to Germany exceeded the volume sent to the second major destination, the Czech Republic (X units), fourfold. The third position in this ranking was taken by Poland (X units), with an X% share.

From 2012 to 2022, the average annual growth rate of volume to Germany amounted to X%. Exports to the other major destinations recorded the following average annual rates of exports growth: the Czech Republic (X% per year) and Poland (X% per year).

In value terms, Germany ($X) remains the key foreign market for injection or compression type moulds for rubber or plastics exports from Italy, comprising X% of total exports. The second position in the ranking was held by Poland ($X), with an X% share of total exports. It was followed by the Czech Republic, with a X% share.

From 2012 to 2022, the average annual growth rate of value to Germany amounted to X%. Exports to the other major destinations recorded the following average annual rates of exports growth: Poland (X% per year) and the Czech Republic (X% per year).

Export Prices by Country

In 2022, the average compression type mould export price amounted to $X per unit, falling by X% against the previous year. Overall, the export price, however, posted a prominent expansion. The most prominent rate of growth was recorded in 2020 an increase of X% against the previous year. Over the period under review, the average export prices reached the peak figure at $X per unit in 2021, and then contracted slightly in the following year.

There were significant differences in the average prices for the major export markets. In 2022, amid the top suppliers, the country with the highest price was the United States ($X per unit), while the average price for exports to Hungary ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was recorded for supplies to Romania (X%), while the prices for the other major destinations experienced more modest paces of growth.

Compression Type Mould Imports

Imports into Italy

In 2022, purchases abroad of injection or compression type moulds for rubber or plastics decreased by X% to X units, falling for the fifth year in a row after three years of growth. In general, imports faced a deep reduction. The growth pace was the most rapid in 2017 with an increase of X%. As a result, imports attained the peak of X units. From 2018 to 2022, the growth of imports failed to regain momentum.

In value terms, compression type mould imports contracted rapidly to $X in 2022. Overall, imports, however, showed a relatively flat trend pattern. The pace of growth was the most pronounced in 2017 when imports increased by X%. As a result, imports reached the peak of $X. From 2018 to 2022, the growth of imports remained at a lower figure.

Imports by Country

China (X units), Germany (X units) and Austria (X units) were the main suppliers of compression type mould imports to Italy, together accounting for X% of total imports. France, Turkey, the Czech Republic, Hungary, Poland, Slovakia, Portugal, Switzerland, Spain and Romania lagged somewhat behind, together comprising a further X%.

From 2012 to 2022, the most notable rate of growth in terms of purchases, amongst the main suppliers, was attained by Hungary (with a CAGR of X%), while imports for the other leaders experienced a decline.

In value terms, China ($X), Germany ($X) and Austria ($X) appeared to be the largest compression type mould suppliers to Italy, together comprising X% of total imports. France, the Czech Republic, Slovakia, Switzerland, Portugal, Spain, Poland, Romania, Turkey and Hungary lagged somewhat behind, together comprising a further X%.

Hungary, with a CAGR of X%, recorded the highest growth rate of the value of imports, in terms of the main suppliers over the period under review, while purchases for the other leaders experienced more modest paces of growth.

Import Prices by Country

In 2022, the average compression type mould import price amounted to $X per unit, dropping by X% against the previous year. Over the period under review, the import price, however, posted buoyant growth. The most prominent rate of growth was recorded in 2020 when the average import price increased by X%. The import price peaked at $X per unit in 2021, and then contracted in the following year.

Prices varied noticeably by country of origin: amid the top importers, the country with the highest price was Switzerland ($X per unit), while the price for Turkey ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was attained by Romania (X%), while the prices for the other major suppliers experienced more modest paces of growth.

Source: IndexBox Platform

Frequently Asked Questions (FAQ) :