Czech Republic: Compression Type Mould Market 2024

Compression Type Mould Market Size in the Czech Republic

In 2022, the Czech compression type mould market was finally on the rise to reach $X for the first time since 2018, thus ending a three-year declining trend. Over the period under review, consumption, however, showed a slight contraction. As a result, consumption attained the peak level of $X. From 2019 to 2022, the growth of the market failed to regain momentum.

Compression Type Mould Production in the Czech Republic

In value terms, compression type mould production skyrocketed to $X in 2022 estimated in export price. In general, production showed a relatively flat trend pattern. The growth pace was the most rapid in 2017 when the production volume increased by X%. As a result, production reached the peak level of $X. From 2018 to 2022, production growth remained at a lower figure.

Join Us at HANNOVER MESSE 2024

Don’t miss your chance to connect with us directly. Schedule a personal meeting to dive deeper into how solutions.
Hall 002, Stand C10. 22 - 26 April 2024 | Hannover, Germany

Book Your Meeting

Compression Type Mould Exports

Exports from the Czech Republic

In 2022, overseas shipments of injection or compression type moulds for rubber or plastics decreased by X% to X units, falling for the fourth consecutive year after two years of growth. In general, exports showed a abrupt curtailment. The most prominent rate of growth was recorded in 2017 when exports increased by X% against the previous year. The exports peaked at X units in 2018; however, from 2019 to 2022, the exports stood at a somewhat lower figure.

In value terms, compression type mould exports declined to $X in 2022. Over the period under review, exports continue to indicate a slight curtailment. The pace of growth was the most pronounced in 2017 when exports increased by X%. The exports peaked at $X in 2013; however, from 2014 to 2022, the exports failed to regain momentum.

Exports by Country

Germany (X units) was the main destination for compression type mould exports from the Czech Republic, with a X% share of total exports. Moreover, compression type mould exports to Germany exceeded the volume sent to the second major destination, Switzerland (X units), fourfold. The third position in this ranking was taken by Poland (X units), with a X% share.

From 2012 to 2022, the average annual growth rate of volume to Germany stood at X%. Exports to the other major destinations recorded the following average annual rates of exports growth: Switzerland (X% per year) and Poland (X% per year).

In value terms, Germany ($X) remains the key foreign market for injection or compression type moulds for rubber or plastics exports from the Czech Republic, comprising X% of total exports. The second position in the ranking was taken by Slovakia ($X), with an X% share of total exports. It was followed by Poland, with a X% share.

From 2012 to 2022, the average annual growth rate of value to Germany stood at X%. Exports to the other major destinations recorded the following average annual rates of exports growth: Slovakia (X% per year) and Poland (X% per year).

Export Prices by Country

In 2022, the average compression type mould export price amounted to $X per unit, surging by X% against the previous year. In general, the export price continues to indicate strong growth. The growth pace was the most rapid in 2020 an increase of X%. The export price peaked in 2022 and is expected to retain growth in the immediate term.

There were significant differences in the average prices for the major foreign markets. In 2022, amid the top suppliers, the country with the highest price was Romania ($X per unit), while the average price for exports to the UK ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was recorded for supplies to France (X%), while the prices for the other major destinations experienced more modest paces of growth.

Compression Type Mould Imports

Imports into the Czech Republic

After three years of decline, overseas purchases of injection or compression type moulds for rubber or plastics increased by X% to X units in 2022. Over the period under review, imports, however, showed a abrupt decline. The most prominent rate of growth was recorded in 2018 with an increase of X% against the previous year. As a result, imports reached the peak of X units. From 2019 to 2022, the growth of imports failed to regain momentum.

In value terms, compression type mould imports contracted to $X in 2022. In general, total imports indicated a noticeable increase from 2012 to 2022: its value increased at an average annual rate of X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations being recorded throughout the analyzed period. Based on 2022 figures, imports decreased by X% against 2018 indices. The growth pace was the most rapid in 2018 with an increase of X% against the previous year. As a result, imports reached the peak of $X. From 2019 to 2022, the growth of imports remained at a somewhat lower figure.

Imports by Country

Germany (X units), China (X units) and Italy (X units) were the main suppliers of compression type mould imports to the Czech Republic, with a combined X% share of total imports. Austria, Portugal, Switzerland, the UK, Russia, South Korea, Poland, Turkey, Slovakia and France lagged somewhat behind, together comprising a further X%.

From 2012 to 2022, the biggest increases were recorded for Turkey (with a CAGR of X%), while purchases for the other leaders experienced mixed trend patterns.

In value terms, the largest compression type mould suppliers to the Czech Republic were Germany ($X), China ($X) and Italy ($X), together comprising X% of total imports. Portugal, Austria, Switzerland, South Korea, Turkey, Slovakia, the UK, Poland, France and Russia lagged somewhat behind, together accounting for a further X%.

Turkey, with a CAGR of X%, recorded the highest growth rate of the value of imports, in terms of the main suppliers over the period under review, while purchases for the other leaders experienced more modest paces of growth.

Import Prices by Country

The average compression type mould import price stood at $X per unit in 2022, waning by X% against the previous year. Over the period under review, the import price, however, posted a strong increase. The most prominent rate of growth was recorded in 2020 an increase of X% against the previous year. The import price peaked at $X per unit in 2021, and then dropped notably in the following year.

There were significant differences in the average prices amongst the major supplying countries. In 2022, amid the top importers, the country with the highest price was Portugal ($X per unit), while the price for Russia ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was attained by Portugal (X%), while the prices for the other major suppliers experienced more modest paces of growth.

Source: IndexBox Platform

Frequently Asked Questions (FAQ) :