CIS: Compression Type Mould Market 2024

Compression Type Mould Market Size in CIS

The CIS compression type mould market shrank remarkably to $X in 2022, waning by X% against the previous year. The total consumption indicated modest growth from 2012 to 2022: its value increased at an average annual rate of X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations being recorded throughout the analyzed period. Over the period under review, the market hit record highs at $X in 2021, and then dropped notably in the following year.

Compression Type Mould Production in CIS

In value terms, compression type mould production reduced to $X in 2022 estimated in export price. The total production indicated a notable expansion from 2012 to 2022: its value increased at an average annual rate of X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations being recorded throughout the analyzed period. Based on 2022 figures, production increased by X% against 2020 indices. The pace of growth was the most pronounced in 2017 when the production volume increased by X% against the previous year. As a result, production attained the peak level of $X. From 2018 to 2022, production growth remained at a somewhat lower figure.

Compression Type Mould Exports

Exports in CIS

For the third consecutive year, the CIS recorded growth in overseas shipments of injection or compression type moulds for rubber or plastics, which increased by X% to X units in 2022. In general, exports enjoyed a resilient expansion. The pace of growth was the most pronounced in 2016 when exports increased by X%. The volume of export peaked in 2022 and is expected to retain growth in years to come.

In value terms, compression type mould exports contracted sharply to $X in 2022. Overall, exports saw a measured expansion. The pace of growth was the most pronounced in 2016 with an increase of X%. The level of export peaked at $X in 2021, and then dropped sharply in the following year.

Exports by Country

Armenia represented the major exporter of injection or compression type moulds for rubber or plastics in the CIS, with the volume of exports recording X units, which was approx. X% of total exports in 2022. It was distantly followed by Russia (X units) and Belarus (X units), together constituting a X% share of total exports. Uzbekistan (X units) and Kazakhstan (X units) took a little share of total exports.

Exports from Armenia increased at an average annual rate of X% from 2012 to 2022. At the same time, Kazakhstan (X%), Uzbekistan (X%), Belarus (X%) and Russia (X%) displayed positive paces of growth. Moreover, Kazakhstan emerged as the fastest-growing exporter exported in the CIS, with a CAGR of X% from 2012-2022. While the share of Armenia (X p.p.), Uzbekistan (X p.p.) and Kazakhstan (X p.p.) increased significantly in terms of the total exports from 2012-2022, the share of Russia (X p.p.) displayed negative dynamics. The shares of the other countries remained relatively stable throughout the analyzed period.

In value terms, Belarus ($X), Russia ($X) and Uzbekistan ($X) were the countries with the highest levels of exports in 2022, with a combined X% share of total exports.

In terms of the main exporting countries, Uzbekistan, with a CAGR of X%, saw the highest growth rate of the value of exports, over the period under review, while shipments for the other leaders experienced more modest paces of growth.

Export Prices by Country

The export price in the CIS stood at $X per unit in 2022, declining by X% against the previous year. Over the period under review, the export price showed a abrupt shrinkage. The most prominent rate of growth was recorded in 2013 an increase of X%. As a result, the export price reached the peak level of $X per unit. From 2014 to 2022, the export prices remained at a lower figure.

Prices varied noticeably by country of origin: amid the top suppliers, the country with the highest price was Belarus ($X per unit), while Armenia ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was attained by Uzbekistan (X%), while the other leaders experienced a decline in the export price figures.

Compression Type Mould Imports

Imports in CIS

In 2022, approx. X units of injection or compression type moulds for rubber or plastics were imported in the CIS; waning by X% compared with the previous year. In general, imports, however, posted tangible growth. The pace of growth was the most pronounced in 2016 with an increase of X% against the previous year. Over the period under review, imports hit record highs at X units in 2021, and then contracted notably in the following year.

In value terms, compression type mould imports shrank sharply to $X in 2022. Overall, imports, however, saw a relatively flat trend pattern. The pace of growth was the most pronounced in 2013 when imports increased by X% against the previous year. The level of import peaked at $X in 2021, and then fell markedly in the following year.

Imports by Country

Russia represented the key importing country with an import of around X units, which finished at X% of total imports. Uzbekistan (X units) took a X% share (based on physical terms) of total imports, which put it in second place, followed by Belarus (X%). The following importers - Kazakhstan (X units) and Tajikistan (X units) - each reached a X% share of total imports.

Imports into Russia increased at an average annual rate of X% from 2012 to 2022. At the same time, Tajikistan (X%), Uzbekistan (X%) and Belarus (X%) displayed positive paces of growth. Moreover, Tajikistan emerged as the fastest-growing importer imported in the CIS, with a CAGR of X% from 2012-2022. By contrast, Kazakhstan (X%) illustrated a downward trend over the same period. Uzbekistan (X p.p.) and Tajikistan (X p.p.) significantly strengthened its position in terms of the total imports, while Kazakhstan and Russia saw its share reduced by X% and X% from 2012 to 2022, respectively. The shares of the other countries remained relatively stable throughout the analyzed period.

In value terms, Russia ($X) constitutes the largest market for imported injection or compression type moulds for rubber or plastics in the CIS, comprising X% of total imports. The second position in the ranking was taken by Uzbekistan ($X), with a X% share of total imports. It was followed by Belarus, with a X% share.

In Russia, compression type mould imports remained relatively stable over the period from 2012-2022. In the other countries, the average annual rates were as follows: Uzbekistan (X% per year) and Belarus (X% per year).

Import Prices by Country

In 2022, the import price in the CIS amounted to $X per unit, waning by X% against the previous year. Over the period under review, the import price showed a noticeable decrease. The most prominent rate of growth was recorded in 2013 an increase of X% against the previous year. Over the period under review, import prices attained the peak figure at $X per unit in 2014; however, from 2015 to 2022, import prices stood at a somewhat lower figure.

Prices varied noticeably by country of destination: amid the top importers, the country with the highest price was Russia ($X per unit), while Tajikistan ($X per unit) was amongst the lowest.

From 2012 to 2022, the most notable rate of growth in terms of prices was attained by Uzbekistan (X%), while the other leaders experienced a decline in the import price figures.

Source: IndexBox Platform

Frequently Asked Questions (FAQ) :